QUICK CASH CAR KIT INC.

Kit- Mini Roadster

These are the photos of the mini roadster kits.

 

Additional kit information:

This kit is an easy conversion kit.  This kit has been installed on a club cart ds model golf cart and completed in two weeks by us working part- time on the project.  Note: the ds cart body is the same from 1989 up to present; however in 2003 the iq model ds version was introduced and the running time was greatly increased. We recommend using the 2003 and newer ds body club cart with the iq computer as the donor vehicle for this mini roadster project.

We suggest the donor be slightly damaged because the body panels will not be used on the finished kit and you will save a lot of money by using a damaged donor cart.  All unused body parts can be resold as scrap or on ebay as reusable body parts. We sell slightly damaged donor carts at great prices.
The stock wheelbase of the ds cart is 65.5” and the wheelbase for the finished mini roadster is 120.5”.  You will extend the frame from the round bar under the dash area by 60.5” and then add 10” as a bumper guard that extends from the front frame out in front of the tires with a plate on each end of each bumper guard. See photos for details.

You will widen the front suspension by 9”. See photos for details.

Cut the center floor board and add 10” in length to the center floor board area of the cart. See photos for details.

Add side rails in the front on each side of the frame rails that are 42” long from the round bar that is located under the dash area of the cart. See photos for details.

The rear area stays the same but you will add the 4” spacers to the hubs.

The seat is 15” high on the back and 37.5” long and then the seat part you sit on is 20” wide x 37.5” long. See photos for details.

Extend the steering column to fit the length of the newly extended frame section.

The battery holder tray is 15.25” outside to outside and we used 2x2” steel tubing. The battery tray has to be 11” on the inside of the tray for the batteries to fit. The batteries will sit inside the frame rails. See photos for details.

The largest wheel size for the finished kit cart that we recommend is a 18” wheel.  You may
 order beautiful wheels from the o.e. wheel co. In Sarasota, Florida by calling 1-866-273-3651 and pay about $558.00 for the wheels shipped with center caps. Ask them for their web-site address to view the wheels on-line. Ask for the hyper-silver, multi-spoke Mercedes styled wheel set and the wheels fit a 2005 slk 350 Mercedes vehicle.

Use wheel spacers to make the roadster wider and we can help you obtain the spacers.  The spacers are 4” on the rear and 2” on the front. We offer all the spacers for $500.00.

You can make the cart run faster. The normal speed for the ds model cart is 12-15 mph but the larger tires make it run about 18 m.p.h. and some people add a larger motor to make it run around 27 m.p.h..

Some people add an outdoor boat type stereo with cd player and a speaker.

Some people add a working horn, lights, etc.

The average turn-key cart is worth $9,000.00 to $15,000.00 and we can teach you how to own a completed cart for around $7,000.00. (donor ds cart $1500.00 + kit $3k + wheels and tires $1k + spacers $500.00 + paint materials $500.00 + misc. $500.00 = $7k) you can own one even cheaper than this example if you use cheaper wheels and do not add any of the extras.

 A $500.00 deposit payable by paypal or check along with a signed purchase order gets your kit started.  Your kit will then be completed within 30 days. Call for details.

We can sell you a real European front car tag with a black plastic holder for $50.00 or you can get one on ebay. Some people put this on the front bumper of the completed car.

This mini roadster kit was inspired by the most beautifully designed German classic car ever created, which is the 1936 Mercedes-Benz 500k special-roadster.
This was the type vehicle that Adolf Hitler was paraded around in during the 1930’s and 1940’s.

‘36 Mercedes 500k roadster =A.F.Y.. = for 95-08 club car golf cart ds model=$2995. Called kit mini Benz
Note: inspired by a 1936 Mercedes-Benz 500k type roadster red

THESE ARE PHOTOS OF THE MINI ROADSTER DURING THE "MOLD PRODUCTION" PROCESS. WE MAKE THE FIRST, VEHICLE-BODY,
PROTOTYPE OUT OF FOAM AND WOOD AND THEN WE MAKE THE FIBERGLASS MOLDS FROM THAT VEHICLE-BODY DESIGN. WE WILL THEN MAKE THE ACTUAL, MINI ROADSTER, BODY-KIT FROM THE COMPLETED FIBERGLASS MOLDS. WE MAKE OUR BODY-KITS AS EASY TO COMPLETE AS POSSIBLE AND THE MINI ROADSTER KIT CAN BE COMPLETED BY ANY PERSON WITH ONLY BASIC, WORK-SHOP SKILLS.

YOU WILL NOT HAVE TO PAY FOR YOUR KIT UNTIL YOU ARRIVE TO PICK-UP YOUR KIT AT OUR FIBERGLASS SHOP. THAT WAY YOU CAN INSPECT THE WORKMANSHIP OF THIS FINE PRODUCT. A PRODUCT THAT WE ARE VERY PROUD TO OFFER AND ONE THAT WE STAND BEHIND WITH A 100% MONEY BACK GUARANTEE. MUCH ENGINEERING AND DESIGN WORKMANSHIP HAS GONE INTO THIS PRODUCT. IT IS LIKE NO OTHER REPLICA KIT OFFERED IN THE WORLD.  MAP QUEST OUR LOCATION AT QUICK CASH CAR KIT INC. 10735 US HIGHWAY 431, ALBERTVILLE AL 35950-0142 OR CALL JACKIE AT 256-891-2030.

-WE ARE NOT AFFILIATED WITH ANY AUTOMOTIVE MANUFACTURER AND WE DO NOT OFFER ANY BADGES, EMBLEMS OR DECALS.

START LIVING YOUR SUPERCAR REPLICA DREAM TODAY.